Windows 10 often get stuck while scanning or while repairing the C or D drive on every startup. The process might stop all of a sudden without any signal. If you are encountering the Windows 10 scanning and repairing drive error, do not worry.
Go through the steps mentioned below offer guidance to fix the Windows 10 getting stuck while scanning and repairing the driver error.
Troubleshoot Scanning And Repairing Drive Stuck Windows 10
The Windows 10 users often complain about encountering the Windows 10 scanning and repairing drive error. To resolve the problem, go through the methods mentioned above.
Method 1: Setting Hard Drive As Boot Drive
You can also fix the Windows 10 scanning and repairing drive by saving it as a boot drive. To do so, you need to go through the following steps:
- Enter the BIOS and then you need to go to the Boot section.
- Now, you need to check the boot priority list.
- However, if the boot drive(SSD/HDD) is not found at the top, make it your number one priority rather than Windows Boot Manager or USB HDD or DVD Rom.
- Now, save and then exit BIOS and reboot your system. When up and running, check if the error persists.
Method 2: Boot In Safe Mode
If you are unable to boot Windows usually, you can try to start it in the boot mode. Look at the following steps:
- First, you need to switch off the computer and wait for a few seconds.
- Now, turn on the PC again.
- You will receive the PC saying that Windows failed to start.
- Now, you need to choose the Advanced Repair options and then hit on the Troubleshoot option.
- When the tab opens, you need to click on Startup Settings under the Advanced Options.
- Now, you need to click on the Restart button and then choose the Safe Mode option and enter into Safe Mode.
- Now, login and then proceed to reboot your the computer.
Method 3. CMD CHKDSK
You can also run a check disk to fix the scanning and repairing drive stuck Windows 10 error. You need to go through the following steps to implement the process:
- First, you need to reboot your system and then press on both the Windows key amd R.
- In the Run dialog box, you need to type cmd. Then choose the Advanced Options and select the Command Prompt.
- When the dialogue box appears on your computer screen, you need to type the ‘fsutil dirty query c:’, ‘chkntfs/xc:’, ‘exit’ commands.
- Finally, restart your computer and check if you are still struggling with the error.
Method 4: Disable Automatic Repair
Also, you can disable the Automatic repair to fix the Windows 10 scanning and repairing drive error. Look at the following steps:
- First, insert the Installation Media and boot from it
- On the bottom left, you will find the ‘Repair your computer’option. Click on it.
- Now, choose the ‘Troubleshoot’ option, followed by the Command Prompt.
- In the dialogue box that appears on your computer, you need to type the ‘bcedit’ command.
- Now, a list you will find the ‘resumeobject’ option. Beside it, you will find a long series of numbers. You need to select the numbers and then press the Enter key.
- Type ‘bcedit/set the long series of the number which was copied in the last step recovery enabled No.
- A message will appear stating that the process was successfully completed.
- Type in the command ‘exit’ and reboot the computer.
Method 5: System Restore
You can also run a system restore to solve the Windows 10 scanning and repairing drive. Restoring will the process again hence, removes all the bugs.
- While restarting the computer, the PC will say that the Windows has failed to start.
- Now, you need to choose the Advanced Repair Options and then select the System Restore option.
- You need to set the date and time and then click on Next.
- Now, click on Finish and reboot your system.
Method 6: System Refresh
If none of the methods work for you, refresh your system. You need a Windows 10 DVD/USB Installation Media for the same process.
- Upon starting the system, your PC will say Windows failed to start.
- Then you need to choose the Advanced Repair Options and then Refresh your PC.
- You need to insert the Installation Media or Custom Installation Media. Then click on the Next option.
- The Windows will start to refresh. The login screen will then appear.
- A list of removed applications in the HTML file will then appear on your computer screen. Finally, you need to reboot the computer you are encountering.